Why Is My RV Losing Power at the Campsite?
Last Updated: November 4, 2026
Quick Summary
RV electrical troubleshooting at campsite starts at the power pedestal, not inside your rig. Unplug your cord, check the pedestal breaker, test the receptacle with a multimeter set to AC volts, and look for scorch marks or a loose fit. If the pedestal reads zero, the problem is the campground's.
A healthy 30-amp receptacle should read close to 120V AC between hot and neutral.
A 30-amp service gives you 3,600 watts; a 50-amp service gives you 12,000 watts across two legs.
Test the converter's 12V output with your multimeter set to DC volts; you want roughly 13.2 to 13.6V DC on shore power.
A GFCI trips at a threshold as low as 5 milliamps to protect people.
Never bypass the surge protector to make it work, since that is how converters and AC units die.
Table of Contents
Start at the Power Pedestal, Not Inside Your RV
RV electrical troubleshooting at campsite starts with one rule we repeat to every owner who calls us: check the pedestal before you touch anything inside your rig.

Here's the sequence we walk customers through. It saves hours of pointless digging.
Unplug your shore power cord from the pedestal.
Look at the pedestal breaker. Is it tripped or half-off?
Test the receptacle with a multimeter set to AC volts.
Check the outlet for scorch marks, melted plastic, or a loose fit.
Plug in a simple tester or a lamp to confirm power is live.
A healthy 30-amp receptacle should read close to 120V AC between hot and neutral. A 50-amp pedestal gives you two hot legs, each near 120V AC. If you get zero, the problem is the campground's, not yours.
Watch out: never force a plug into a receptacle that feels loose or shows burn marks. That's a fire risk, and it usually means the pedestal's contacts are worn out.
What the Pedestal Breakers and Receptacles Tell You
A tripped pedestal breaker usually means one of two things: the campground's circuit is overloaded, or something in your RV is pulling too much amperage. Reset it once. If it trips again the moment you plug in, stop and look inward.
Loose receptacles are the quiet culprit. Years of RV plugs going in and out wear down the contacts, and a loose connection creates heat. Heat melts plastic. That's how pedestals fail.
Check the receptacle face for discoloration every time you plug in. It takes five seconds and prevents a lot of grief.
Before you touch anything inside your rig, run through this pedestal check in order.
Step | What to do |
1 | Unplug shore power cord from the pedestal |
2 | Check pedestal breaker for tripped or half-off |
3 | Test receptacle with multimeter set to AC volts |
4 | Look for scorch marks, melted plastic, loose fit |
5 | Plug in a simple tester or lamp |
RV Electrical Converter Troubleshooting: When 12V Systems Go Quiet
RV electrical converter troubleshooting begins with one question: are your 12V DC items dead while your 120V AC outlets still work? If yes, the converter is the prime suspect. The converter is the device that turns campground AC power into the 12V DC your lights, water pump, and fridge control board need.
Here's how we narrow it down:
Check the converter's breaker in your main panel. It's often labeled "CONV" or "Converter."
Look for the cooling fan. Most converters hum or blow air when working. Silence is a clue.
Test the 12V output at the converter terminals with your multimeter set to DC volts. You want to see roughly 13.2 to 13.6V DC when plugged into shore power.
Inspect the reverse polarity fuses. Most converters have two blade fuses on the front. A blown pair usually means the battery was connected backward at some point.
If the converter reads zero output but has power coming in, it has failed. A replacement unit is one possible fix, and a tripped 12V fuse in the panel is another cause to rule out.
A common mistake is replacing the converter before checking the fuse panel. Always start at the fuses.
30 Amp vs 50 Amp RV Power Issues: Reading the Right Symptoms
The 30 amp vs 50 amp RV power issues split comes down to one number: how much power you can pull at once. A 30-amp service gives you 3,600 watts. A 50-amp service gives you 12,000 watts across two legs. That gap explains almost every symptom difference between the two setups.
On 30-amp service, you'll see:
Breakers tripping when the AC and microwave run together
Lights dimming when the fridge compressor kicks on
A warm cord end after a long run
On 50-amp service, you'll see:
One leg dead while the other works (a classic lost-leg symptom)
Half your outlets dead, half fine
The rig acting "possessed" with random appliance failures
That lost-leg pattern trips up a lot of owners. If half your 120V outlets work and half don't, you likely have a bad leg at the pedestal or a failed connection in your transfer switch. Test each leg separately at the pedestal before you blame the RV.
For 30-amp owners, the fix is usually load management. Run the AC, then the microwave, not both at once. Know your wattage budget and stay under it.
Tracing the Fault: Breakers, GFCIs, and Loose Connections
Once you've cleared the pedestal, work inward through breakers, GFCIs, and connections in that order.
Start at the main breaker panel. Flip each breaker fully off, then back on.
Next, check the GFCI outlets, usually in the bathroom, kitchen, and exterior compartment. Press the reset button firmly. If it won't stay set, you have a ground fault somewhere downstream on that circuit.
Then look for loose connections. Shut off power at the pedestal and the main breaker first. Check the lugs on your breakers and the neutral bar.
Electrical safety guidance from the Consumer Product Safety Commission is worth reading before you open any panel. RV electrical safety is not the place to guess.
Resetting a GFCI That Won't Stay Set
A GFCI that trips the moment you reset it is telling you something is wrong, not that the outlet is broken. The GFCI is doing its job. It senses current leaking to ground somewhere on that circuit, and it trips at a threshold as low as 5 milliamps to protect people.
Unplug everything on the circuit. Reset again. If it holds, plug items back one at a time until it trips. The last item you plugged in is the culprit. If it trips with nothing plugged in, the fault is in the wiring itself, and that's a job for a pro.
Watch out: never replace a tripping GFCI with a standard outlet to "make it stop." That removes the ground-fault protection and turns a nuisance trip into a shock hazard.
Voltage Drop and Surge Protector Diagnostics
Voltage drop is the sneaky one. Your pedestal might read a healthy 120V with nothing plugged in, then sag to 108V or lower once your AC kicks on. Low voltage cooks motors and control boards, and it's often the campground's wiring, not yours. This is the most commonly misdiagnosed campsite electrical problem because the rig appears to have "lost power" when it actually has weak power.
Symptoms of voltage drop include:
Lights dimming when appliances start
AC compressor struggling to start or humming without kicking over
Appliances running hot or shutting off randomly
A microwave that runs slow or a converter that never reaches full charge
A surge protector with a voltage readout is your best diagnostic tool here, and it is the first thing to check before you open any panel. The codes are your shortcut to the fault:
Low voltage (often shown as L1 or L2 low): the pedestal is sagging under load. Move sites or ask management to check the pedestal; do not bypass the protector.
High voltage: a miswired or failing pedestal transformer. Unplug and report it.
Open ground or open neutral: the pedestal wiring is faulty. This is a campground fix, not an RV fix.
Reverse polarity (hot and neutral swapped): do not plug in. Reverse polarity can energize the RV chassis and is a shock hazard.
Lost leg on 50-amp service: one hot leg is dead. Half your 120V outlets will work and half won't. Test each leg at the pedestal before blaming the transfer switch.
When a protector shuts off power and shows a code, believe it. That code is protecting your rig. If your surge protector keeps cutting power at the same campground, move sites or ask management to check the pedestal. Don't bypass the protector to "make it work." That's how converters and AC units die.
Isolating Generator Power From Shore Power
Generator and shore power should never meet. The transfer switch is the device that keeps them apart, and when it fails, you get weird symptoms: dead outlets on shore power, a generator that won't carry the load, or a burning smell near the switch.
Test it this way. With shore power unplugged, start the generator. If 120V items work, the generator side is fine. Plug into shore power and shut the generator down. If items go dead, the transfer switch isn't moving back to shore power.
Never run both at once, and never bypass the transfer switch. The switch exists to prevent backfeeding, which can injure utility workers and damage your rig. If the switch buzzes, smells hot, or clicks repeatedly, stop using it and get it looked at.
When to Stop Diagnosing and Call Sharp RV Services
There's a point where DIY diagnosis stops being smart and starts being risky. If you've tested the pedestal, reset the breakers, checked the GFCIs, and the problem persists, the fault is likely inside a panel or behind a wall. That's when you call us.
At Sharp RV Services, we bring the repair to your campsite or storage lot, so you don't have to break camp and tow your rig across Pinellas County. We work on all types of RVs and handle electrical faults alongside AC, water, and appliance issues.
You can review the services we offer or contact us to schedule a visit and get back to your trip. Get started with Sharp RV Services and let us handle the technical work while you enjoy the road.
Frequently Asked Questions
Why are my RV outlets not working when I'm on shore power?
Work through the chain in order. Check that the pedestal breaker is on and the receptacle has power, then confirm your shore power cord is fully seated at both ends. Inside the RV, look for a tripped main breaker or a tripped GFCI outlet, since one GFCI upstream can kill several downstream outlets. If the 120V AC side checks out but your lights and fans are dead, the problem is on the 12V DC side and points to the converter or battery bank rather than the outlets themselves.
How can I tell if my RV converter or inverter is failing?
A failing converter usually shows up as 12V items dimming or dying while you are plugged into shore power, or a battery bank that never reaches full charge. Check the converter's output with a multimeter at the fuse panel; a healthy unit holds roughly 13.2 to 13.6 volts DC in normal operation. Inverters fail differently: 120V outlets fed by the inverter go dead while shore power still works, or the unit trips its own breaker repeatedly. Either way, confirm the converter or inverter is actually receiving 120V AC before you replace it.
What is the first thing I should check when the whole RV loses power at a campsite?
Start at the pedestal. Confirm the campground breaker is switched fully on, then test the receptacle with a multimeter or plug in a surge protector with a diagnostic light. Pedestal breakers trip often, especially on hot days when everyone runs air conditioning, and a partially seated shore power cord causes the same symptom. Only after the pedestal and cord check out should you open your own breaker panel, and never probe inside it with the shore power connected.
When should I call a professional mobile RV repair service instead of troubleshooting myself?
Call a professional when you smell burning, see scorched or melted connections, or find wiring corrosion you cannot safely clean and re-terminate. The same applies if breakers trip repeatedly after reset, if voltage at the pedestal reads low or fluctuates, or if the fault sits behind the breaker panel where live conductors are exposed. A mobile technician can test the transfer switch, converter, and wiring on site, which beats guessing at a campground with limited tools.



Comments