top of page
Search

How to Light an RV Water Heater Pilot in 7 Steps

edsharp333
6 days ago
8 min read

Is your RV water heater refusing to light?

Sharp RV Services brings mobile repair to your RV across Pinellas County.

Table of Contents

Before You Light the Pilot: Safety Checks and Water Level

Last Updated: November 14, 2026

Knowing how to light an RV water heater pilot is simple, but never rush it. Many owners skip basic checks and end up with a pilot that will not stay lit. Five minutes of preparation saves time and keeps you safe.

Before you touch the control knob, confirm these things:

  • The tank has water. Running a water heater dry can damage the heating element or the tank itself.

  • Propane is on. Check the propane tank valve and make sure the level is not empty.

  • The area is ventilated. Open a window or vent near the unit. Propane is heavier than air and can collect in closed spaces.

  • No gas smell. If you smell rotten eggs or gas, do not light anything. Shut off the propane and get outside.

  • No open flames nearby. Turn off the stove, furnace and any candles before you begin.

Watch out: never attempt to light the pilot while the water tank is empty. Doing so can destroy the heater.

Once you know the tank is full and the gas is safe, you are ready to move on.

Identify Your Ignition Type: Pilot Button or Electronic Igniter

RV water heaters use one of two ignition types, and the most common mistake is trying to light a manual pilot on a unit designed to spark automatically, or the reverse. Identify your system before touching anything, the steps, safety rules and failure modes differ.

Manual-pilot system. You will see a gas control valve with a rotary knob marked Off, Pilot and On, plus a push button or knob you press down. A sight glass or small opening near the burner lets you watch the flame.

Electronic-ignition system. You will see a rotary or rocker switch, often with a spark symbol, and hear rapid clicking when it is on. There is no push-and-hold pilot button. The control module opens the gas valve, sparks the burner and monitors the flame.

How to tell them apart. With the access door open, a push-and-hold button or a knob you must depress signals a manual pilot. A switch that clicks and ticks repeatedly signals electronic ignition. A flame icon with a lightning bolt means electronic; a "Pilot" label with an arrow to a push position means manual.

Check the data plate. Every water heater has a model and serial label, usually on the frame near the access opening or inside the compartment. Write down the model number and look it up in the owner's manual before lighting.

Why it matters for safety. On a manual-pilot unit you are introducing an open flame into the burner area, so confirm ventilation and no gas odor first. On an electronic-ignition unit, never use a hand lighter, the module may spark unexpectedly and a flame can cause a flash. Follow the appliance label.

Quick rule. If you must press and hold a button to keep gas flowing to the pilot, it is manual and you light it by hand. If you flip a switch and hear clicking, it is electronic and you should never put a flame near the burner.

Comparison diagram for how to light an RV water heater pilot showing manual knob versus electronic ignition.

How to Light an RV Water Heater Pilot Step by Step

Follow these steps in order. The process takes about five minutes once you are familiar with it.

  1. Open the access panel. Find the access door on the outside of the RV, usually near the water heater compartment. Open it fully.

  2. Turn the control knob to "Pilot." Set the knob to the pilot position. Do not turn it to "On" yet.

  3. Turn on the propane supply. Make sure the propane valve is open.

  4. Push and hold the control button. Press the knob or button down and keep it pressed.

  5. Light the pilot. Hold a long lighter or match near the pilot opening. If you have an electronic igniter, press the igniter button instead.

  6. Keep holding the button. Continue pressing for 30 to 60 seconds. This heats the thermocouple, which keeps the gas flowing.

  7. Release the button slowly. If the flame stays lit, the pilot is working. If it goes out, repeat the steps.

Watch out: do not hold the button down for more than about one minute while lighting. Give the thermocouple time to heat, then stop and try again if the flame does not hold.

Lighting with a Built-In Igniter Versus a Hand Lighter

A built-in igniter is quicker and safer because you do not reach into the access area with a flame. Press the igniter, hold the control and let the spark light the pilot.

A hand lighter works on any unit but takes more care. Keep the flame at the pilot opening only, keep your face and clothing away from the panel, and use a long-nozzle lighter so your fingers stay clear.

The steps below sum up the lighting sequence described in the article.

Step

What to do

Time or frequency

1. Open access panel

Open the door fully

Before lighting

2. Set knob to Pilot

Do not turn to On yet

Before lighting

3. Turn on propane

Make sure the valve is open

Before lighting

4. Push and hold button

Keep pressed during lighting

Hold 30-60 seconds

5. Light the pilot

Long lighter or igniter button

During hold

6. Keep holding

Let thermocouple heat

30-60 seconds

7. Release slowly

Confirm flame stays lit

After flame holds

How to Turn On Electric Water Heater in RV Models

Some RVs have a combination unit that runs on both propane and electricity. Electric mode works when the RV is plugged into shore power or running a generator.

To turn on the electric element:

  • Make sure the tank is full of water.

  • Find the electric switch, usually labeled "Elec" or with a lightning bolt symbol.

  • Switch it on. The heater will take roughly 30 to 60 minutes to heat the water, depending on the tank size.

  • Switch it off when you are finished, or when you leave the RV unplugged for long periods.

Electric mode does not use the pilot light, so it works even when the pilot is out. Electric heating is often slower than propane, so plan ahead.

Atwood Water Heater Pilot Lighting Instructions

A pilot is typically lit as follows:

  1. Turn the knob to "Pilot."

  2. Press and hold the knob down.

  3. Light the pilot through the opening with a long lighter.

  4. Keep holding for about 30 to 60 seconds.

  5. Release the knob. If the flame stays lit, turn the knob to "On."

Manufacturer manuals may give slightly different timings, so check yours. If the pilot will not light, confirm the propane supply and try again.

Dometic and Other Models: Pilot Light Troubleshooting

Brands differ in layout, but troubleshooting is similar. On many units, look for a control with a clearly marked pilot position and a small window to see the flame.

Common problems across models include:

  • No propane reaching the unit. Check the tank valve and the regulator.

  • Air in the gas line. After a tank change or long storage, air can block the flow. Hold the button longer on the first attempt.

  • Dirty pilot opening. Debris, spider webs or dust can block the flame. Clean the opening gently with a soft brush.

  • Faulty thermocouple. This sensor tells the valve to stay open. If it is worn out, the pilot will light but go out quickly.

If you cannot identify your model or the problem persists, look up the exact model number before ordering parts.

When the RV Water Heater Pilot Light Won't Stay Lit

A pilot that lights and then dies when you release the button is the most common complaint on manual-pilot units, and the cause is almost always on a short list.

First, rule out a gas safety problem. If you smell rotten eggs or propane at any point, do not relight.

1. You released the button too early. The thermocouple sits in the pilot flame and generates a tiny voltage that holds the gas valve open, but it needs time to heat.

2. The thermocouple is misaligned or dirty. Its tip must sit in the flame, not beside or above it. If bent away, the flame heats air instead of the sensor and the valve closes.

3. The thermocouple has failed. If correctly positioned and held long enough but still will not hold the valve open, it is likely worn out.

4. Air in the gas line. After a tank change, long storage or running out of propane, the line can fill with air. The first attempt may need a longer hold while propane reaches the burner.

5. A weak or dirty pilot orifice. Spider webs, dust and rust scale are common in the pilot opening and burner tube.

6. Drafts across the burner. Wind entering the open access panel can blow out a healthy pilot. If the pilot holds with the panel partly closed but dies when the panel is fully open, draft is the cause.

7. Low or unstable propane pressure. A nearly empty tank, a failing regulator, or a two-stage regulator that is not delivering correctly can produce a flame too weak to hold the thermocouple. Check the tank level first.

When to stop and call for service. Stop DIY attempts if you smell gas, if the flame is consistently large and yellow, if a replaced thermocouple does not fix it, or if the gas valve is suspect.

Booking Help When Your RV Water Heater Won't Light

If the fixes above do not work, it may be time for professional help. Some causes, a faulty gas valve, a bad thermocouple or a regulator problem, need tools and experience to fix safely.

Sharp RV Services provides mobile repair and maintenance for recreational vehicles throughout Pinellas County, so you do not have to haul your RV to a shop. Visit our Services page for more information. When you are ready to get a visit scheduled, contact our team with your RV model and a description of the problem.

Pricing depends on the repair, parts and time required. For current pricing or a quote, reach out to Sharp RV Services directly.

Frequently Asked Questions

How do I light the pilot on my RV water heater?

Confirm the tank has water and the propane valve is open. Set the water heater switch to off, then turn the gas control to pilot. Press and hold the control down, light the pilot with a long lighter or use the igniter, and keep holding for about 30 to 60 seconds after the flame appears. Release the button and check that the flame stays lit. Then turn the control to the on or burner position and set the thermostat. If the flame goes out when you release the button, wait a few minutes and try again.

Can I relight my RV water heater pilot myself?

Yes, most RV owners can relight a pilot themselves if the propane supply is on, the tank is full of water, and the access panel and pilot opening are clear. Follow the same steps used to light it originally, holding the control for 30 to 60 seconds after ignition. If the pilot repeatedly fails to stay lit, or you smell gas, stop, ventilate the area, and call a qualified technician rather than continuing to attempt the repair.

How can I tell if my RV water heater uses a pilot light or electronic ignition?

A pilot-style water heater has a visible pilot button or control knob marked pilot and requires a flame you light by hand or with an igniter. Electronic ignition models typically have a switch or button that produces a clicking spark when pressed, and often include an indicator light. Check the label inside the access panel or the owner's manual for the model number, then confirm the ignition type before you begin, since the steps differ.

Why won't my RV water heater pilot light stay lit?

The most common causes are a control knob not held down long enough after ignition, air in the gas line after the propane tank was run low, a dirty or partly blocked pilot opening, or a faulty thermocouple that fails to sense the flame. Make sure you hold the button for 30 to 60 seconds, check the propane supply, and clean debris from the pilot area. If the flame still goes out, stop trying and schedule professional service with Sharp RV Services for an inspection.

 
 
 

Comments


RV MOBILE REPAIR | SHARP RV SERVICES | CLEARWATER

727-804-9554

  • Facebook
  • Facebook

©2021 by Sharp RV Services. Proudly created with Wix.com

bottom of page